8/17/2023 0 Comments Edison arduino kit![]() ģ.Have run the Wi-Fi car server and smart phone received the dashboard but can’t controll the rover. ![]() If you want only to visit the linux system you can connect its WiFi AP and visit via SSH tools, the PuTTy is capable of SSH. FAQġ.If you have connected the Edison’s WiFi and the dashboard was shown but can’t controll the rover.Ģ.The two USB ports on Edison Arduino board were blocked by a wheel what to do to connect USB cables?Ī:You have to take down the wheel when you want to connect USB cables. Goto the virtual terminal open car.py do the below change. Plug the grove cables to D4(D4,D5) D8(D8,D9) with no special definition, test the connection by plug the battery. Step 3.Connect the power wire and two grove cables. Step 2.Assemble the motor and the motor driver,pay attention to the yellow arrows, two motor drivers are screwed with only two screw. Here you'll need a wire stripper a soldering iron and scissors to cut down the motors' extension wires, and use one of them to make a new one-to-two motor power cable. Navigate to /usr/share/car you’ll see the project, these files are: Now use a smart phone or computer to search the WiFi accessible point, the SSID was named in a unique serier numbers by the S/N id on every edison main board like EDIOSN-FZED445001UCV501, and the passphrase is 12345678.Īfter connected to the WiFi, open any web browser visit you’ll see a dashboard with which to controll the 4WD Platform. >cd edison-image-rel1-maint-rel1-ww42-14-for-car >7z x edison-image-rel1-maint-rel1-ww42-14-for-wificar.7z >unzip edison-image-rel1-maint-rel1-ww42-14-for-wificar.zip See Intel Edison official web site "Alternate Flashing Method". Edison reboot and Wi-Fi Car service started.ĭisconnect and reconnect the battery. Go to PuTTy input command line reboot or press the RESET button on the Edison Arduino board. Right click This PC > Advanced system setting > Environment Variables > copy the path of dfu-util.exe to catch the “Path” environment variable.ġ.Download and unzip Download customized firmware from seeed wiki Download customized firmware from google driveĭownload customized firmware from onedriveįollow the official Edison Getting Started Guide to log in edison with PuTTy. If you want to know what we have done in the linux system and how to do your own project see the github repository:įollow the Edison official web site getting started to install required drivers and the terminal emulator PuTTy.ĭownload dfu-util - Device Firmware Upgrade Utilities and extract the xz file to “C:\” or any other directory. The only thing you should do to have this platform work is to flash a new firmware into Edison. The most important resource is the mraa library which provided by Intel, things aren’t that idealized that there are difficulties in our early development, in order to build a convenient development Environment we copy the partition of rootfs out of the linux file system in which we have already configured all the needed resource and built the 4WD platform project. 3.Continue assembling Development EnvironmentĪlthough the Edsion Arduino can be programed by arduino IDE but for stronger development we got into the linux system to do some low level development. Use a nylon cable to tie up the wires,then plug the grove cable.ĥ)Put on the middle board, the power cable and the grove cable were to across the right hole.Ħ)Plug the 1-to-2 power connector the battery adapter cable and the arduino board power cable, the grove cable connect to A0 pin of the Base Shield.ħ)Carefully plug the battery connector to get power up, test if it was right done now, if no led light up you must check the problem.Ĩ)Plug the USB cables to test the software. 2.Connect the cablesġ) Below are the parts with cables to be connected, you need a 2.5mm Slotted head screwdriver to srew the motor driver.Ģ)Stick the aluminum heatsinks to the chips on the motor driver, and assemble the middle board.ģ)Connect the motor driver,the motor group's black cables connect to "M1-" "M2-" and the red ones connect to "M1 " "M2 ", connect the power cable,the black cable to "GND", the red one to "VS".Ĥ)Assemble the motor group into the main body, the motor in the same group must assemble to the same side. Grove - Universal 4 Pin Buckled 20cm CableĪssembly Instruction.pdf 1.Assemble the main body. Screw, Spring Lock Washer and Plain Washer assemblies This is a primary project if you are a maker and ability to hack this platform welcome to do a stronger remake.Ĭross Recessed Pan Head Screw with Washer The 4WD Auto Robotic Platform is a powerful mobile unit with the Intel Edison Arduino kit, to control this platform you have to use a smart phone or a computer with wifi capable to connect to its wifi accessible piont, open a web browser input the address than a operation dashboard comes up.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |